Bascom und AVR Dragon

Hallo,
wie kann ich den AVR Dragon in Bascom einbinden?
Phyton_rocks hatt bereits am 17.01 einige gute Anmerkungen dazu gemacht (Danke). Es muss eine cmd datei erstellt werden.
der Inhalt soll für einen Atmega8 wie folgt aussehen:

C:\Programme\Atmel\AVR Tools\AvrDragon\AVRDragon.exe" -d ATmega8 -e -mi -pf -if %1
pause


Welche bedeuungen haben dabei die optionen?

Gibt es weitere Möglichkeiten den Dragon in Bascom zu implementieren?

Zitat:

---

Zitat von maikatze

C:\Programme\Atmel\AVR Tools\AvrDragon\AVRDragon.exe" -d ATmega8 -e -mi -pf -if %1
pause

Welche bedeuungen haben dabei die optionen?

---

Hallo maikatze!

Führe das Programm "AVRDragon.exe" mit dem Kommandozeilenparameter "-h" aus. (z.B. so: "AVRDragon.exe -h"). Dann bekommst du eine Erklärung der Kommandozeilenparameter ausgegeben.

Das sieht dann so aus:

Code:

---

Usage: avrdragon.exe [commands] [options]
Commands:
 -h, -?                Print this help.
 -he                Print exit codes.
 -e                Erase device.
 -f <fusebytes>        Write high/low fuse bytes. The LSB of fusebytes will be
                written to the low fuse byte, and the MSB will be written
                to the high fuse byte.
 -j <ID>        Read JTAG ID string. If an optional ID is specified, the
                program will terminate if the read ID differs.
 -l <lockbyte>        Set the lock byte to the specified value.
 -p[f|e|b]        Program FLASH (-pf), EEPROM (-pe) or both (-pb) memories.
                Requires input files specified with the -if (FLASH)
                and/or -ie (EEPROM) options.
 -q                Read fuse bytes. If the selected device has extended fuse,
                it will be also be read.
 -r[f|e|b]        Read FLASH (-rf), EEPROM (-re) or both (-rb) memories.
                Requires output files specified with the -of (FLASH) and/or
                -oe (EEPROM) options.
 -s                Read signature bytes.
 -v[f|e|b]        Verify FLASH (-vf), EEPROM (-ve) or both (vb) memories.
                Requires input files specified with the -if (FLASH) and/or
                -ie (EEPROM) options.
 -y                Read lock byte.
 -E <ext.fuse>        Write extended fuse byte.
 -F <fusebytes>        Verify high/low fuse bytes. The LSB of fusebytes will be
                compared to the low fuse byte, and the MSB will be compared
                to the high fuse byte.
 -L <lockbyte>        Verify the lock byte.
 -G <ext.fuse>        Verify the extended fuse byte against the given value.
 -O <address>        Read oscillator calibration byte. Address is location of byte
                as specified in the device's data sheet.
 -S[f|e] <address>
                Write oscillator calibration byte read with -O or -Z to given
                location in FLASH (-Sf) or EEPROM (-Se).
 -W                Disable debugWIRE interface, enabling ISP mode. Only available
                for debugWIRE devices.
 -Y                Perform the oscillator calibration sequence. See appnote
                AVR053 for more information.
 -Z <address>        Load value from address in EEPROM prior to erasing the device.
                This value can be written to FLASH or EEPROM again with
                the -S[f|e] command.

Options:
 -ae <start>,<end>
                Specify address range for reading EEPROM memory. Default is
                entire memory.
 -af <start>,<end>
                Specify address range for reading FLASH memory. Default is
                entire memory.
 -d <device>        [required] Specify the type of device.
 -ie <file>        Specify input file for programming EEPROM memory.
 -if <file>        Specify input file for programming FLASH memory.
 -m[i|j|p]        Choose programming mode: ISP (-mi), parallel/high-voltage (-mp)
                or JTAG (-mj) (default).
 -oe <file>        Specify output file for reading EEPROM memory.
 -of <file>        Specify output file for reading FLASH memory.
 -z                No progress indicator. Useful when redirecting output to file.
 -D <devsbefore,devsafter,bitsbefore,bitsafter>
                Set daisy chain settings. Only available in JTAG mode.
 -I <speed>        Specify ISP frequency (Hz). Only available for ISP mode.
 -J <speed>        Specify device speed (Hz). Only available for JTAG mode.
 -R                Apply external reset while programming. Only available in
                JTAG mode.

Example usage: avrdragon.exe -d ATmega128 -e -pf -if c:\tmp\test.hex

Supported devices:
        AT90CAN128, AT90CAN32, AT90CAN64, AT90USB1286, AT90USB1287,
        AT90USB646, AT90USB647, ATmega128, ATmega1280, ATmega1281,
        ATmega16, ATmega162, ATmega164P, ATmega165, ATmega165P,
        ATmega169, ATmega169P, ATmega2560, ATmega2561, ATmega32,
        ATmega324P, ATmega325, ATmega3250, ATmega3250P, ATmega325P,
        ATmega329, ATmega3290, ATmega3290P, ATmega329P, ATmega406,
        ATmega64, ATmega640, ATmega644, ATmega644P, ATmega645,
        ATmega6450, ATmega649, ATmega6490
Supported devices for ISP, PARALELL/SERIAL HV mode and oscillator cal. only:
        AT90PWM2, AT90PWM216, AT90PWM2B, AT90PWM3, AT90PWM316, AT90PWM3B,
        AT90USB162, AT90USB82, ATmega168, ATmega168P, ATmega16HVA,
        ATmega48, ATmega48P, ATmega88, ATmega88P, ATtiny13, ATtiny2313,
        ATtiny24, ATtiny25, ATtiny261, ATtiny44, ATtiny45, ATtiny461,
        ATtiny84, ATtiny85, ATtiny861

---

mfg
Gerold
:-)